What work did you just do?

[Cwlongshot]

I would love to get a LDC on my steroid Dan.... Cannot shot it outside here as its too loud.. 

CW

[bgmcgee]

Nice streak there ped.   Those have to be one of those must have airguns, thankfully my parents gave me one for Christmas when I was 13. As for me I unboxed the 2260 tore it apart cleaned the batrel added a nice aluminum breech chongman handle d.c.probe and Williams peep sight and shot it.

[ped]

cheers lads i've always liked them
i'll see if i can source one for you cw as i've pm'd a chap on a uk forum about getting a barrel and tube for a 70's rocker safety one and he used to make them
looks like i'm going to have to pull the valve on this one as when you pump it half the air on the pump stroke is venting down the barrel i'm presuming its the later valve with the two orings and the front one is allowing air past
ped

[rangerfredbob]

Last night I tore the M4-177 apart, lightened the trigger pull, flat topped the valve, next step is to make a piston, might figure out how to get an O ring breech seal in...

[arkmaker †]

Added the steel breech, LDC and scope to the 2260.

[Cwlongshot]

cheers lads i've always liked them
i'll see if i can source one for you cw as i've pm'd a chap on a uk forum about getting a barrel and tube for a 70's rocker safety one and he used to make them
looks like i'm going to have to pull the valve on this one as when you pump it half the air on the pump stroke is venting down the barrel i'm presuming its the later valve with the two orings and the front one is allowing air past
ped

I had one that did that.. it was the flapper in the valve. (Technical term ''flapper''. )

I appreciate the help on the part!!

CW

[ped]

pulled the valve tonight on my streak and it was green inside plus the front o ring felt hard so 1/2 hour with the valve in some coke and a bit of scrubbing with brasso and it was clean again ,new orings and put it back together and all's well again
got a reply reguarding the adapter and he has one cw but hasn't given me a price once i get one i'll pm you then you can deal direct with him or i can get it then forward it onto you
ped

[Cwlongshot]

pulled the valve tonight on my streak and it was green inside plus the front o ring felt hard so 1/2 hour with the valve in some coke and a bit of scrubbing with brasso and it was clean again ,new orings and put it back together and all's well again
got a reply reguarding the adapter and he has one cw but hasn't given me a price once i get one i'll pm you then you can deal direct with him or i can get it then forward it onto you
ped

AWESOME NEWS!!

Thank you brother ped!! 

I mounted a Williams peep on my Walther Talon Magnum 25cal... shoots good FEELS a WHOLE lot better too!! Its a BIG gun, removing the scope, made it ALOT easier to handle!





CW

CW

[targettgii]

I took the utg cantilever base off my 1322 and replaced ti with bkl offset rings no pics yet.

[Bazmati2020]

Just started on my 1322 that I was going to keep stock 

Steel breech, Benjamin grips & an LPA MIM sight.

Pistol HFT at weekend so I'll give it a run out

http://postimg.org/image/ruo2q5it5/

[img=http://s28.postimg.org/ruo2q5it5/image.jpg]

[Bazmati2020]

Just started on my 1322 that I was going to keep stock 

Steel breech, Benjamin grips & an LPA MIM sight.

Pistol HFT at weekend so I'll give it a run out

http://postimg.org/image/ruo2q5it5/

[img=http://s28.postimg.org/ruo2q5it5/image.jpg]

[BDS]

So Nice that he posted it Twice! 

[K.O.]

Increased valve volume of my stock 1377 by about 2 threads, slight easing of corner of air passage, thinned poppet shaft and coned head,  matched nose of valve to pump cup, still need to shim cup back out, tops out at 550fps with a seated 7.4 pointed Crosman,  a gain of 20-30fps  16 pumps. This is in prep for 1760se barrel ordered last week.

I also increased valve volume of my  1322 by almost 3 threads,  a touch of hogging out the thick walls of the front  portion, air passage eased 3/4 of way to poppet seat, poppet shaft thinned and coned head, cup/valve already matched but need shimmed much more than the five thicknesses of pop can I used, enlarged transfer and barrel port size  to just over .140/ a loose 9/64,  tops out at 550 fps @ 17 pumps a gain of 10- 15 fps.

Installed new pump tube (old one had some deep scratches) for the 853..

[WyoMan]

nice valve work K.O.  pretty decent gains....
are you using a lighter valve spring?

[K.O.]

nice valve work K.O.  pretty decent gains....
are you using a lighter valve spring?

http://www.crosman-air-pistol-owners-forum.com/board/index.php/topic,13048.0.html